🚀 Lifetime Access launches soon. Create a free account to grab free models now.
← All guides

Troubleshooting · 7 min read

Wet filament and clogged nozzles: how to spot, fix and prevent them

Popping, stringing and rough surfaces usually mean wet filament. Here is how to test it, drying temperatures for PLA, PETG and TPU, storage tips, and how to clear a clogged nozzle with a cold pull.

A spool that printed perfectly last month suddenly strings, pops and leaves rough walls. Nine times out of ten the filament has absorbed water from the air. Left alone, wet filament can also lead to a clogged nozzle. Here is how to deal with both.

Signs of wet filament

  • Popping or crackling sounds from the nozzle while printing
  • Bubbles, pits or a rough, fuzzy surface
  • Much more stringing than usual
  • Weak, brittle parts that split along the layers
  • Brittle filament that snaps in the feed path (common with old PLA)

Quick test: heat the nozzle and push some filament through by hand. Dry filament comes out smooth and quiet. Wet filament sputters, steams and leaves a bubbly strand.

How to dry it

Use a filament dryer or a food dehydrator. A kitchen oven is risky: its thermostat swings can soften the spool. Take the spool off the printer first.

Filament Temperature Time
PLA 45 to 50 °C 4 to 6 hours
PETG 60 to 65 °C 4 to 6 hours
TPU 45 to 50 °C (no higher than 55 °C) 4 to 8 hours
ABS / ASA 65 to 80 °C 4 hours
Nylon 70 to 80 °C 8 to 12 hours

Check your filament maker's settings, which win over any table.

How to store it

  • Airtight bins or vacuum bags with silica gel desiccant
  • A cheap hygrometer in the box: aim for under 20% relative humidity
  • Recharge silica gel in a dryer or oven when its indicator changes color
  • Avoid garages and basements, where humidity swings with the weather

Flexible and engineering filaments absorb water fastest. TPU, nylon and PETG need the most care. See How to print TPU.

Clogged nozzle: what it looks like

  • Partial clog: thin, gappy lines, or extrusion that stops and comes back.
  • Full clog: nothing comes out, and the extruder clicks or grinds.

First, rule out the easy causes: a tangled spool, a nozzle too close to the bed on the first layer, or a temperature that is too low for the material.

How to clear it

  1. Heat and push. Heat to printing temperature and gently push filament by hand. Use light pressure only: forcing it can damage the hotend.
  2. Cold pull. Heat the nozzle, push filament through, let it cool to about 90 °C for PLA (or follow your printer's guide), then pull it out firmly. The tip pulls out the debris with it. Repeat until the tip comes out clean. Nylon cleaning filament works best.
  3. Cleaning needle. For a small blockage at the tip, a thin cleaning needle from below can break it up. Never drill or widen the nozzle.
  4. Replace the nozzle. Nozzles are cheap. If a clog keeps coming back within a day, swap it. Many current printers have tool-free nozzle swaps.

Always follow your printer's manual, and let the hotend cool before you touch it.

Prevent clogs

  • Keep filament dry.
  • Print within the material's temperature range.
  • Lower the temperature, or swap to a fresh spool, if you see heat creep (soft filament jamming above the nozzle).
  • Clean the nozzle with a brass brush now and then.

Related: How to fix stringing, warping and other common problems and First layer troubleshooting.

Want models that are already set up for your printer?

Every Trove3D file ships with a tested 3MF profile. Start with three free ones.

Get the Free Starter Pack