🚀 Lifetime Access launches soon. Create a free account to grab free models now.
← All guides

Troubleshooting · 8 min read

How to fix stringing, warping and other common 3D print problems

A plain-English troubleshooting guide for the problems beginners search for most: stringing, warping, poor bed adhesion, under-extrusion, clogs and wet filament.

Almost every failed print comes down to a handful of causes. This guide covers the ones people search for most, in the order you should check them. For first-layer problems specifically, see Troubleshooting your first layer.

The golden rule: change one setting at a time and print a small test. If you change three things at once, you never learn which one fixed it.

Stringing (thin "spider webs" between parts)

Stringing happens when molten plastic oozes from the nozzle while it travels between parts.

Check, in this order:

  1. Wet filament. This is the number one cause, especially for PETG and TPU. Wet filament pops and hisses as it prints. Dry it (see below) and try again before touching any setting.
  2. Temperature too high. Lower the nozzle temperature by 5 °C at a time. A temperature tower test print shows the sweet spot in one go.
  3. Retraction. Increase retraction distance or speed a little. Direct-drive printers usually need 0.5 to 2 mm; Bowden printers 4 to 6 mm. Too much retraction can cause clogs.
  4. Travel moves. Enable "avoid crossing walls" or "combing" in your slicer so the nozzle stays inside the part.

Small wisps that brush off are normal for PETG. A quick pass with a heat gun or lighter removes them.

Warping (corners lifting off the bed)

Plastic shrinks as it cools. When the top layers shrink, they pull the corners up.

Fixes:

  • Clean the bed with warm water and dish soap, or isopropyl alcohol. Fingerprints are enough to ruin adhesion.
  • Raise the bed temperature a little (PLA 55 to 65 °C, PETG 70 to 85 °C).
  • Add a brim of 5 to 8 mm. It gives the corners something to hold on to.
  • Stop drafts. An open window, an air conditioner vent or a ceiling fan can cool one side of the print. An enclosure helps a lot with ABS and ASA.
  • Slow the part cooling fan for the first few layers.
  • Round sharp corners in your own designs, which spreads the stress.

The print does not stick at all

  • Level or re-run the auto bed leveling, and set the Z offset so the first layer is slightly squished.
  • Slow the first layer to 20 to 30 mm/s.
  • Make sure you are using the right plate for the material: PETG can bond too well to smooth PEI and tear it, so use a textured plate or a glue stick as a release layer.

Under-extrusion (gaps, thin walls, weak parts)

  • Partial clog: heat the nozzle and push filament through by hand, or do a cold pull. If the nozzle is old, replace it: nozzles are cheap.
  • Tangled or tight spool: check that the spool turns freely.
  • Printing too fast for the temperature: high-speed printing needs a hotter nozzle or a high-flow hotend.
  • Wrong filament diameter or flow in the slicer profile.

Layer shifts

The print suddenly jumps sideways partway up.

  • A belt is loose, or the nozzle hit a curled-up part. Tighten belts and fix the curling (see warping).
  • Lower acceleration for very tall prints.

Elephant's foot (first layers bulge out)

The first layer is squished too much or the bed is too hot. Raise the Z offset slightly or enable "elephant foot compensation" in your slicer.

Wet filament: the hidden cause of many problems

Filament absorbs moisture from the air. Symptoms: popping sounds, steam, stringing, rough surfaces and brittle filament that snaps.

  • Dry it: a filament dryer, or an oven you have checked with a separate thermometer (PLA about 45 to 50 °C, PETG about 65 °C, for 4 to 6 hours). Many ovens run hotter than the dial says.
  • Store it: sealed bags or boxes with desiccant packs.

Test prints that help

  • 3DBenchy: overhangs, bridges, small holes and fine text in one hour
  • All-in-one printer test: supports, scale, overhangs, holes and bridging on one plate
  • Temperature tower: finds the best nozzle temperature for a new spool

Browse more test pieces in Desk Toys & Test Prints and the Workshop category.

Want models that are already set up for your printer?

Every Trove3D file ships with a tested 3MF profile. Start with three free ones.

Get the Free Starter Pack